Cookiewet mededeling:
Dit forum gebruikt cookies. Klik op het kruisje aan de rechterkant om akkoord te gaan met het gebruik van cookies.
This forum uses cookies. Click the X icon on the right to agree using cookies.
Dit forum gebruikt cookies. Klik op het kruisje aan de rechterkant om akkoord te gaan met het gebruik van cookies.
This forum uses cookies. Click the X icon on the right to agree using cookies.
2jz-gte shimless buckets guide
- Tjabbo
- ShoarmaTeam Admin
- Posts: 24489
- kuchnie na wymiar
- Joined: Tuesday 21 February 2006 17:31
- Location: Vroomshoop
- Contact:
2jz-gte shimless buckets guide
2JZ-GTE Shimless Buckets Guide
Measure the valve clearance, then remove all buckets keeping them numbered as to where they go, use a micrometer and measure their thichness, calculate desired clearance, go to Toyota and order valve buckets for a MR-2 spyder they are availabel in .02mm incriments, fit perfectly no machining required cost about 300$ for all 24. I did it to mine and seems to rev a little smoother at higher rpm.
This removes 12 ounces or more from the valvetrain depending on how thick the original shims were.
Whats the difference?
The shimless buckets outside surface is much thinner compared to a Shim. The Shimless bucket on the inside has a center tip (refer to picture above) that veries in length making up the total thickness.
Where as a Shim has the same thickness for the entire diameter of the bucket.
So less material=less weight.
This is mostly helpfull for High lift camshafts so the shims don't get shot out. (not really a problem on the 2jz or 3s) but on a 7m or 4a they are absolutely needed with high lift camshafts.
But for people looking for every single performance upgrade possible even to get that 10th of a horsepower, reducing valve train weight will help.
Am I supposed to measure with the shim still in the bucket?
Yes. You should have not removed them. You must measure the old bucket with the shim still in it. Do not remove the shims off the buckets before measuring it may cause you to be off by a .001" to .002" if the shim isn't sitting perfectly on the bucket.
Place the shim back in the bucket and make sure to push it down hard and ensure that the shim is seated.
If you have mismatched the shims and buckets you need to retake your valve clearance and start over. (meaning you don't know if you put the same shim back on the same bucket)
Adding the shim thickness to the bucket thickness should work, but will most likely give you a slightly inacurate reading. It is better to take one measurement.
Part #'s for Shimless Buckets:
Here are the part numbers and sizes for the shimless buckets:
13751-46030 5.06 mm
13751-46040 5.08
13751-46050 5.10
13751-46060 5.12
13751-46070 5.14
13751-46080 5.16
13751-46090 5.18
13751-46100 5.20
13751-46110 5.22
13751-46120 5.24
13751-46130 5.26
13751-46140 5.28
13751-46150 5.30
13751-46160 5.32
13751-46170 5.34
13751-46180 5.36
13751-46190 5.38
13751-46200 5.40
13751-46210 5.42
13751-46220 5.44
13751-46230 5.46
13751-46240 5.48
13751-46250 5.50
13751-46260 5.52
13751-46270 5.54
13751-46280 5.56
13751-46290 5.58
13751-46300 5.60
13751-46310 5.62
13751-46320 5.64
13751-46330 5.66
13751-46340 5.68
13751-46350 5.70
13751-46360 5.72
13751-46370 5.74
________________
Measure the valve clearance, then remove all buckets keeping them numbered as to where they go, use a micrometer and measure their thichness, calculate desired clearance, go to Toyota and order valve buckets for a MR-2 spyder they are availabel in .02mm incriments, fit perfectly no machining required cost about 300$ for all 24. I did it to mine and seems to rev a little smoother at higher rpm.
This removes 12 ounces or more from the valvetrain depending on how thick the original shims were.
Whats the difference?
The shimless buckets outside surface is much thinner compared to a Shim. The Shimless bucket on the inside has a center tip (refer to picture above) that veries in length making up the total thickness.
Where as a Shim has the same thickness for the entire diameter of the bucket.
So less material=less weight.
This is mostly helpfull for High lift camshafts so the shims don't get shot out. (not really a problem on the 2jz or 3s) but on a 7m or 4a they are absolutely needed with high lift camshafts.
But for people looking for every single performance upgrade possible even to get that 10th of a horsepower, reducing valve train weight will help.
Am I supposed to measure with the shim still in the bucket?
Yes. You should have not removed them. You must measure the old bucket with the shim still in it. Do not remove the shims off the buckets before measuring it may cause you to be off by a .001" to .002" if the shim isn't sitting perfectly on the bucket.
Place the shim back in the bucket and make sure to push it down hard and ensure that the shim is seated.
If you have mismatched the shims and buckets you need to retake your valve clearance and start over. (meaning you don't know if you put the same shim back on the same bucket)
Adding the shim thickness to the bucket thickness should work, but will most likely give you a slightly inacurate reading. It is better to take one measurement.
Part #'s for Shimless Buckets:
Here are the part numbers and sizes for the shimless buckets:
13751-46030 5.06 mm
13751-46040 5.08
13751-46050 5.10
13751-46060 5.12
13751-46070 5.14
13751-46080 5.16
13751-46090 5.18
13751-46100 5.20
13751-46110 5.22
13751-46120 5.24
13751-46130 5.26
13751-46140 5.28
13751-46150 5.30
13751-46160 5.32
13751-46170 5.34
13751-46180 5.36
13751-46190 5.38
13751-46200 5.40
13751-46210 5.42
13751-46220 5.44
13751-46230 5.46
13751-46240 5.48
13751-46250 5.50
13751-46260 5.52
13751-46270 5.54
13751-46280 5.56
13751-46290 5.58
13751-46300 5.60
13751-46310 5.62
13751-46320 5.64
13751-46330 5.66
13751-46340 5.68
13751-46350 5.70
13751-46360 5.72
13751-46370 5.74
________________
My blue manual 1989 1JZ Supra twin turbo
My grey automatic 1991 Supra turbo
Whenever a bird shits on my car I eat a plate of scrambled eggs on my front porch, just to show them what I'm capable of.
My grey automatic 1991 Supra turbo
Whenever a bird shits on my car I eat a plate of scrambled eggs on my front porch, just to show them what I'm capable of.
- Tjabbo
- ShoarmaTeam Admin
- Posts: 24489
- Joined: Tuesday 21 February 2006 17:31
- Location: Vroomshoop
- Contact:
Re: 2jz-gte shimless buckets guide
shimless buckets excel helper:
http://www.boostsamurai.com/SupraShimle ... aPolak.xls
http://www.boostsamurai.com/SupraShimle ... aPolak.xls
My blue manual 1989 1JZ Supra twin turbo
My grey automatic 1991 Supra turbo
Whenever a bird shits on my car I eat a plate of scrambled eggs on my front porch, just to show them what I'm capable of.
My grey automatic 1991 Supra turbo
Whenever a bird shits on my car I eat a plate of scrambled eggs on my front porch, just to show them what I'm capable of.
Re: 2jz-gte shimless buckets guide
Waaarom kan ik de bestand niet openen?Tjabbo wrote:shimless buckets excel helper:
http://www.boostsamurai.com/SupraShimle ... aPolak.xls
dit krijg ik in een link
Windows bezit de volgende gegevens over dit bestandstype. Op deze pagina kunt u de software zoeken waarmee u het bestand kunt openen.
Bestandstype: Onbekend
Beschrijving: Dit bestandstype wordt niet door Windows herkend.
Op de volgende websites vindt u een volledige lijst met bestandsextensies. Mogelijk vindt u daar informatie over dit bestandstype:
help me out tjabbo
"It's not about what car you have,it's about what you can do to it..........yourself !!!"
- Tjabbo
- ShoarmaTeam Admin
- Posts: 24489
- Joined: Tuesday 21 February 2006 17:31
- Location: Vroomshoop
- Contact:
Re: 2jz-gte shimless buckets guide
dan moet je microsoft excel installeren, dan werkt het wel.
edit:
excel is niet gratis.
je kan wel een 'viewer' downloaden maar dan kan je niets bewerken en dat is jammer.
want je kan een getal invoeren bij 'desired intake' en dergelijke en dan berekent hij wat je hebben moet voor shimms.
viewer:
http://www.microsoft.com/downloads/deta ... laylang=EN
edit:
excel is niet gratis.
je kan wel een 'viewer' downloaden maar dan kan je niets bewerken en dat is jammer.
want je kan een getal invoeren bij 'desired intake' en dergelijke en dan berekent hij wat je hebben moet voor shimms.
viewer:
http://www.microsoft.com/downloads/deta ... laylang=EN
My blue manual 1989 1JZ Supra twin turbo
My grey automatic 1991 Supra turbo
Whenever a bird shits on my car I eat a plate of scrambled eggs on my front porch, just to show them what I'm capable of.
My grey automatic 1991 Supra turbo
Whenever a bird shits on my car I eat a plate of scrambled eggs on my front porch, just to show them what I'm capable of.
- krammetje
- Elite shoarma voorproever
- Posts: 2568
- Joined: Saturday 22 July 2006 00:27
- Location: Almelo
Re: 2jz-gte shimless buckets guide
dus deze buckets kan ik zo zonder problemen in mijn 3s-gte kop passen?
Hmm een bucket kost zo'n 17 euro... x 16 in mijn geval da's 300 euri.
Is het wel een hele upgrade dan ipv shim under bucket?
Als je nu shim over bucket hebt, dan zie ik het grote voordeel wel, met shims die onder de nokkenas uit kunnen komen.
In het geval van shim under bucket kan dat dus al niet.
K zal eens kijken .
Hmm een bucket kost zo'n 17 euro... x 16 in mijn geval da's 300 euri.
Is het wel een hele upgrade dan ipv shim under bucket?
Als je nu shim over bucket hebt, dan zie ik het grote voordeel wel, met shims die onder de nokkenas uit kunnen komen.
In het geval van shim under bucket kan dat dus al niet.
K zal eens kijken .
ST205WRC sold
Megane Scénic pour la famille BHG
Focus station
Megane Scénic pour la famille BHG
Focus station
Re: 2jz-gte shimless buckets guide
Hmm Volgens mij breng je het een en ander door de waarkrammetje wrote:dus deze buckets kan ik zo zonder problemen in mijn 3s-gte kop passen?
Hmm een bucket kost zo'n 17 euro... x 16 in mijn geval da's 300 euri.
Is het wel een hele upgrade dan ipv shim under bucket?
Als je nu shim over bucket hebt, dan zie ik het grote voordeel wel, met shims die onder de nokkenas uit kunnen komen.
In het geval van shim under bucket kan dat dus al niet.
K zal eens kijken .
Shims UNDER buckets is beter als je bv je kop gaat aanpassen met andere klepveren etc etc om hogere toeren te draaien
Dus andere klepveren msichien andere kleppen je kop flowen etc etc dat pas moet je shims UNDER BUCKETS
Maar als je bv gewoon andere camgears heb met bv andere nokkenasen vind ik het zonde van het geld want je gaat toch geen 9/10 000 toeren draaien
"It's not about what car you have,it's about what you can do to it..........yourself !!!"
- Tjabbo
- ShoarmaTeam Admin
- Posts: 24489
- Joined: Tuesday 21 February 2006 17:31
- Location: Vroomshoop
- Contact:
Re: 2jz-gte shimless buckets guide
correct me if i'm wrong maar krammetje heeft een 3rd gen 3sgte en DUS heeft hij al shim under buckets.
no need for upgrades.
gewoon speling meten, nokas er af, tonnetje er uit, shim er uit, nieuwe shim er in, tonnetje er in en nokas er weer op.
klaar.
no need for upgrades.
gewoon speling meten, nokas er af, tonnetje er uit, shim er uit, nieuwe shim er in, tonnetje er in en nokas er weer op.
klaar.
My blue manual 1989 1JZ Supra twin turbo
My grey automatic 1991 Supra turbo
Whenever a bird shits on my car I eat a plate of scrambled eggs on my front porch, just to show them what I'm capable of.
My grey automatic 1991 Supra turbo
Whenever a bird shits on my car I eat a plate of scrambled eggs on my front porch, just to show them what I'm capable of.
Re: 2jz-gte shimless buckets guide
Tjabbo wrote:correct me if i'm wrong maar krammetje heeft een 3rd gen 3sgte en DUS heeft hij al shim under buckets.
no need for upgrades.
gewoon speling meten, nokas er af, tonnetje er uit, shim er uit, nieuwe shim er in, tonnetje er in en nokas er weer op.
klaar.
Klopt
"It's not about what car you have,it's about what you can do to it..........yourself !!!"
- krammetje
- Elite shoarma voorproever
- Posts: 2568
- Joined: Saturday 22 July 2006 00:27
- Location: Almelo
Re: 2jz-gte shimless buckets guide
Ik heb idd. al shim under bucket.
No need for upgrades dus , mooi dan laten we het zo.
No need for upgrades dus , mooi dan laten we het zo.
ST205WRC sold
Megane Scénic pour la famille BHG
Focus station
Megane Scénic pour la famille BHG
Focus station
Re: 2jz-gte shimless buckets guide
Nice info, daar was ik naar op zoek